How To Install A Wireless Backup Camera

Download Article

A rear-view camera, too known equally a backup photographic camera, lets you see what'southward behind your vehicle without having to wait backwards. Though the device comes standard with many new car models, yous can add a rear-view camera to your vehicle if it didn't come with one.

1
Purchase a mountable backup camera for your specific vehicle. For safety, make sure you buy a device specifically designed to exist a rear-view camera. Purchasing one made for your specific vehicle will make it easier to install than a standard aftermarket camera. So you can install it easily, look for a camera that mounts onto or straight behind your license plate.^[1]
- Look for backup cameras at consumer electronics stores.
2
Get an external monitor if yous want to proceed your existing rear-view mirror. An external backup monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they take up more space than internal monitors, external monitors are far easier to meet and tin be easily replaced if necessary.
- If you'd similar, you can use a standard video monitor instead. Even so, keep in mind that it may not have all the aforementioned features as devices designed for use with backup cameras.
Advertisement
3
Buy an internal monitor for a less obtrusive device. An internal backup monitor is a fully performance rear-view mirror that houses a minor screen inside the drinking glass. Some internal monitors prune on superlative of your current rear-view mirror, just others replace your original mirror entirely.^[2]
- Nearly internal monitors shut off and disappear when not in use, making them a perfect option if you want to preserve your machine's looks.
4
Buy power and video cords if your camera and monitor didn't include them. For most rear-view camera installations, you lot'll need camera and monitor splitter cords with connectors for video and power cables, ii bare wire power cables, and an RCA video cable.^[3]
- Most installation kits include these cables, only some may require you to purchase them separately.
- Some camera models use wireless transmitters instead of standard video cables.
Advertisement

1
Take off your rear license plate. Using a Phillips head screwdriver, remove each of the screws holding your rear license plate in place. And so, pull the plate off and set it aside.^[four]
- Make sure you place the screws in a safety place so you don't lose them.
ii
Remove your body'south interior panel. Pop open your body and look for a solid interior panel covering the contrary side of your license plate mounting surface area. Then, insert a trim removal tool or other thin device behind the panel and pry it off.^[5]
- Removing this panel will expose the motorcar's rear wiring chambers.
3
Drill a small hole in the license plate mounting area. Brand sure there are no obstructions between the license plate mount and the rear wiring sleeping room. Then, create a pocket-size hole in the auto using a power drill equipped with a high-speed twist drill bit. Line up your pigsty so it is directly behind where your camera's power and video cablevision will become.^[6]
- To effigy out where to make the hole, hold your camera up to the area you intend to mount information technology. And then, note the spot where its splitting cord sits.
- Create a hole that's large enough to fit your camera'south power and video cable.
- If you come across any obstructions, effort to remove them. If you can't, come across if y'all can make a hole nearby.
- For well-nigh jobs, you'll need a drill flake that has a bore between ¹⁄₈ and ¹⁄₄ in (0.32 and 0.64 cm).
4
Place a rubber grommet around your camera cablevision. Before running your camera cable into the car, slip a rubber grommet onto information technology nearly the non-splitting end. These small rubber washers, available at most abode improvement stores, will continue the wire in place and forestall leaks.^[7]
- Choose a grommet that'south only large plenty to fit inside the drilled hole.
5
Run the camera cable into your trunk. Pull the splitting end of your camera's video and ability cablevision through the drilled pigsty into the body of your automobile. Brand sure you pull it tight and so the rubber grommet lodges into the drilled hole.
- Your camera cable should run from the exterior of the automobile to the inside of the car.
6
Locate your car's 2 reverse light wires. Reverse light wires are the cords that connect your car'southward tail lights to the dashboard. They hook straight into your vehicle's tail lights and are ordinarily located in the hatch or torso of your automobile.
- These cords wait different for every vehicle so, if you can't find them, consult your owner'south transmission for model specific data.
seven
Strip and separate your car'south reverse calorie-free wires. Using a wire stripper or pliers, pare back the rubber covering the wires. Then, use a screwdriver or other thin tool to poke a hole through the center of each exposed wire, separating the individual wire strands.^[eight]
- For safety, brand sure you exercise this while the automobile is turned off.
eight
Fuse your camera wires with the reverse low-cal wires. Attach ane of your bare wire cables to the camera string's power connector. And then, poke your bare wires through the center of the exposed reverse lite wires and twist them together. For rubber, make sure you wrap the combined wires in electric tape.^[9]
- Make certain you poke your positive (usually red) bare wire through the positive opposite low-cal wire and the negative (usually black) bare wire through the negative contrary light wire.
Advertising

ane
Route your camera'southward video cable to the forepart of the auto. Connect your RCA cable to the camera cord'due south video connector if necessary. Then, run information technology through your vehicle to the surface area past the fuse box. Depending on your vehicle model, you'll usually exist able to do this by peeling back the motorcar's headliner or side panels and pulling your cablevision through the exposed chamber.^[10]
- For sure trucks, y'all may need to run the video cable through the vehicle's frame track.
- In most cars, yous'll notice the fuse box underneath the steering bicycle.
2
Prepare external monitors to the forepart windshield. If you're installing an external monitor, first adhere your device'south included mount to the windshield by following the manufacturer's included instructions. And so, hook your monitor onto the mount.
- Virtually external monitors use a suction mount, though others may come up with a more circuitous mounting arrangement.
three
Attach internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll need to clip the new device onto your current rear-view mirror. For others, y'all'll need to accept off the mirror and slide your monitor into the pre-existing mirror mount.^[11]
- Some internal monitors may come with their own mounting system that you'll have to attach to the car's front windshield.
4
Run the monitor's splitter cable to the fuse box. If necessary, claw your monitor's power and video cable into the device. Then, route the cable from the monitor to the area next to the fuse box.^[12]
- If y'all'd like, apply a trim removal tool to pop out the headlining console directly above your windshield. Then, run your cable through the exposed chamber.
5
Connect your monitor'due south camera cable to the RCA cablevision. After routing your monitor'due south splitter cable, connect the video end of the cablevision to your photographic camera'southward RCA cord. And so, wrap the continued cords with electrical tape to concord them together.
- If your RCA and video cables accept the same ends, you may need to buy an RCA male to female person converter cord. Yous can notice these at most electronic stores.
six
Attach your monitor'due south power cablevision to a fuse tap. Connect your remaining bare wire cablevision to the backup monitor's power cord. And then, push the positive (usually scarlet) end of the bare wire cablevision into the open end of a fuse tap. Finally, crimp the 2 cables together with a pair of pliers.^[13]
- A fuse tap is a small cable that converts a bare wire into a fuse signal. You can notice them at most auto part stores.
- If yous'd prefer, you can go out the bare wire cable off and connect your photographic camera's power cablevision to a cigarette lighter adaptor. Then, plug this adaptor into your car's cigarette lighter receptacle for power.
7
Plug the fuse tap into the fuse box. Locate your fuse box and open information technology up. Then, plug your fuse tap into an open up fuse cell. If necessary, check your fuse box'south lid or your vehicle'southward instruction manual to see which slots are open.^[fourteen]
- After attaching your fuse, consider taping all your wires together using electrical tape to get them out of the way.
Advertizement

one
Connect your fill-in camera to its power and video cable. Return to the dorsum of your automobile once you've installed the rear-view monitor and all the necessary camera cords. Close the trunk if necessary, and then connect the backup photographic camera to its ability and video cablevision.
- Your camera's power and video cable should be sticking out of the hole you drilled in the license plate mounting area.
two
Mount the camera to your license plate. If the camera attaches to the front of your license plate, set it to the plate by post-obit the manufacturer'due south included instructions. If the camera attaches to the back of your license plate, line the device up with the plate's fastener holes and thread screws through them.^[15]
- In nigh cases, you lot tin attach a rear-view camera to the back of your license plate using the screws you removed from the automobile earlier.
3
Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. One time you've reattached it, give the license plate and backup camera firm tugs to brand sure they're secure.
- If you haven't already, reattach your automobile's interior trunk panel and other trim panels by pressing them back onto the vehicle.
four
Examination the photographic camera to make sure everything works. Before using your new camera on public roads, test it in a safe area like your driveway. If it turns on, place a big, durable object like a trash can behind the camera to encounter how distorted the prototype is. If it does not plow on, read your installation transmission for troubleshooting information.
- In many cases, rear-view camera malfunctions are caused by loose or improperly connected wires.
Advertisement

Add New Question

Question

I hooked the camera upwardly and information technology just flickers. Whatever communication?

You may desire to ensure all cables and connections are secured tightly. Double bank check that all connections are right. If this doesn't piece of work, check to see if the camera chosen is in adept shape and isn't physically damaged.
Question

Suzuki installed reverse parking camera in my Swift Dzire Zxi. Just the camera shows upper view and non the ground beneath. What can I do ?

Brand sure that the camera is installed the correct way (not upside downwards), and check the position of the camera mounted. Have it back to the dealer that installed it and enquire them to check the alignment and fit.
Question

What is the best summit for a reversing camera?

There is no optimal summit for a back-up camera. The ideal superlative is based off the specific automobile or vehicle that you accept and your personal preferences, along with its intended awarding. Some redundancy cameras are placed on large service trucks so that they tin line up to trailer hitches easier, some are to prevent a blindspot on the road. Depending on your awarding, it can be placed at any height. Almost reversing cameras are a "wide view" style and the specific height location does non e'er affect the mode it functions.

Inquire a Question

200 characters left

Include your email accost to become a bulletin when this question is answered.

Submit

Though most car dealers and mechanics will not install aftermarket fill-in camera systems, many audio and electronic shops will.

Make sure you turn the car off earlier working with bare or stripped wires. If you demand to touch exposed wires while the car is on, put on a pair of shock-resistant rubber gloves.

Things You'll Need

Rear-view camera
Rear-view monitor
Connector cables
Phillips head screwdriver
Trim removal tool
Power drill with high-speed twist bit
Rubber grommet
Wire stripper or pliers
Electrical record
Fuse tap

About This Article

Article Summary Ten

To successfully install a rear-view photographic camera, first remove your vehicle's rear license plate and interior trunk panel. Using a power drill, dial a small pigsty through the exposed license plate mounting surface area and run your camera's power and video cord through it. Adhere a bare wire power cablevision to your camera's power connector, then strip your car'southward reverse lite wires and splice them with your bare wire power cable. To learn how to mount the rear-view camera and backup monitor, scroll down!

Did this summary help you?

Thanks to all authors for creating a folio that has been read 245,215 times.